Kronobat Go12V18Ah · Traction battery 12V Litio
Specifications
| Brand | KRONOBAT |
|---|---|
| Voltage (V) | 12,8 |
| Capacity (C20) | 18Ah (c20) |
| Technology | LiFePo4 |
| Length | 168.00mm |
| Width | 175.00 |
| Height | 125.00 mm |
| Weight | 2.00 Kgs |
€165.70
VAT included
Kronobat Go12V18Ah 12.8V 18Ah is a traction battery for industrial electric vehicles: forklifts, pallet trucks, elevating platforms, cleaning machines (scrubbers) and golf buggies. Built for deep discharges and 8-hour continuous work cycles.
Why this traction battery?
- Industrial designbuilt for 8 hours of continuous daily work
- Deep discharges without damagefully recovers when recharged
- Long industrial lifespanpays back the investment over time
Voltage
12.8 V
Capacity
18 Ah
Dimensions
168×175×125 mm
Technology
Lithium (LiFePO4)
Weight
2 kg
Golf cart battery Kronobat Go12V18Ah 18Ah 12.8V
12.8VVoltage
18AhCapacity
2kgWeight
The 12.8 V, 18 Ah Kronobat Go12V18Ah with LiFePO4 lithium technology is designed for golf carts and electric utility vehicles. It replaces the original battery without adaptation in golf carts with a 168 × 175 × 125 mm format: same 18 Ah capacity.
- LiFePO4 lithium: minimal weight and almost zero self-discharge.
- Daily deep discharges without capacity loss.
- Sealed and maintenance-free.
- Full recharge every night with the vehicle charger.
What the Kronobat Go12V18Ah is for
The Kronobat Go12V18Ah is designed for golf carts and electric utility vehicles: deep discharges every day and a full overnight recharge. Check that it matches your current battery in dimensions, terminals and hold-down: this reference has a weight of 2 kg.
Technology inside the Kronobat Go12V18Ah
The Go12V18Ah is one of the Kronobat references for this type of use; it shares the same manufacturing and quality-control criteria as the rest of the brand's catalogue.
LiFePO4 chemistry is the safest of the lithium batteries: thermally stable, cobalt-free and good for thousands of cycles, protected by its electronic management system.
Dimensions, polarity and mounting
It has external dimensions of 168 × 175 × 125 mm and weighs 2 kg. For a direct replacement, the current battery tray must accept these dimensions and the same terminal layout; otherwise adapters will be needed or the hold-down will change.
What Kronobat does differently
With Kronobat we offer an own-brand alternative without compromising on quality: European manufacturing, original-equipment controls and the direct backing of baterias.com for warranty and advice. All the Kronobat batteries in our catalogue are genuine product, recently manufactured and covered by the manufacturer's warranty.
How to make it last longer
Recharge the set fully after each round and avoid routine discharges below 20%. Always replace all the batteries in the bank at once and use the charger specified by the vehicle manufacturer.
Manufacturer's warranty
The Kronobat Go12V18Ah comes with the manufacturer's official warranty against manufacturing defects. If it fails through a defect within the warranty period, we replace it at no cost to you.
When you get it and how to return it
Same-day dispatch from our warehouse for in-stock orders placed before 6:00 pm: 24-48 working hours in mainland Spain and Portugal, 3 to 5 days in the islands and the rest of Europe. Returns are accepted for 14 days if the battery has not been used (free collection on the Iberian mainland). You will receive tracking by email.
BCOM-KRONOBAT-Go12V18Ah
Data sheet
- Reference
- Go12V18Ah
- Voltage (V)
- 12,8
- Length
- 168.00mm
- Width
- 175.00
- Height
- 125.00 mm
- Weight
- 2.00 Kgs
- Technology
- LiFePo4
- Capacity (C20)
- 18Ah (c20)
Recommended accessories
How to change the battery
Guide to replace a cyclic battery (12V 4-30Ah) for UPS, mobility scooter, alarm or backup device. Estimated time 10-15 minutes. Important: discharge residual voltage before handling.
Step 1. Power off and unplug the device
Unplug the device (UPS, scooter, alarm) and leave it off for at least 30 seconds to discharge residual capacitor voltage. Work on an insulating surface.
Step 2. Locate the battery compartment
Usually under the seat (mobility scooter/wheelchair), in the rear module of the UPS, or behind a side panel with screws. Check the device manual for unusual models.
Step 3. Disconnect the negative (−) first
With insulated gloves, remove the negative (−) cable first. Some UPS have protection fuses — note their position before removing.
Step 4. Disconnect the positive (+) terminal
Repeat with the positive cable (red, marked +). Important: never let a terminal touch metal of the car while the other is still connected.
Step 5. Remove the old battery
Typical weight 1-15 kg depending on capacity. Many cyclic batteries are AGM/GEL — keep them upright. Do NOT invert the battery: even sealed, residue may exist.
Step 6. Fit the new battery
Same orientation and type (AGM, GEL or flooded). Polarity must match the device, not a chassis (this is not a car). Make sure terminals do not touch metal parts of the compartment.
Step 7. Connect the positive (+) first
On cyclic devices the order is reversed compared to cars: positive (+) first, negative (−) afterwards. Tighten without forcing — the plastic terminal housing of cyclic batteries damages easily.
Step 8. Initial charge before first use
Cyclic batteries ship at 60-80%. Before first use, connect the device charger for 8-12 hours (or use an AGM/GEL smart charger if available). This avoids short cycles and extends lifespan.
Frequently asked questions
How do I change this battery step by step?
In most devices it fits in 15-30 minutes with a 10 mm wrench; if the battery is under the seat or in the boot the time can double. See the step-by-step guide on this page. Quick summary: 1) switch off the engine and remove the key; 2) locate the original battery (engine bay, boot or under seat); 3) disconnect the negative (−) terminal first, then the positive (+); 4) loosen the hold-down clamp and remove the old battery; 5) fit the new one in the same orientation — match the polarity shown on the product sheet; 6) connect the positive (+) first, then the negative (−). On devices with Start-Stop or BMS, register the battery via OBD so the alternator applies the correct charging profile.
How long does the Kronobat BCOM-KRONOBAT-Go12V18Ah battery last?
Expected lifespan of the Kronobat BCOM-KRONOBAT-Go12V18Ah is 10 to 15 years, equivalent to 3,000-5,000 cycles at 80% DoD. In cold regions it drops slightly due to cold-start stress; in very hot regions it also drops because of electrolyte evaporation. To extend its life: avoid deep discharges (headlights on with engine off), have the alternator checked yearly, and keep the battery clean and properly secured.
What are the dimensions of the Kronobat BCOM-KRONOBAT-Go12V18Ah battery?
Dimensions (length × width × height) are 168×175×125 mm — also written as 168x175x125 mm — following the European DIN standard. Always measure the space in your device before buying: even one extra millimetre can prevent the hold-down clamp from closing. The height shown includes the terminals.
Which batteries are equivalent to the Kronobat BCOM-KRONOBAT-Go12V18Ah?
Directly interchangeable batteries (same dimensions, same polarity, same Ah and CCA) are the OEM equivalents from leading brands: Bosch, Tudor, Exide and, depending on the model, Banner or Yuasa. Exact equivalence depends on technology — an EFB cannot be replaced with a conventional battery in Start-Stop devices. See the "Equivalents" section to view recommended options at the same performance level.
The top-rated online battery store in Spain
-
Audited by Trustpilot, no filters, no edits. The top-rated battery store in Spain.
Trustpilot · verified, no filters
-
Official Varta distributor
Official Varta wholesale distributor. 100% genuine batteries, recently manufactured, best price and no middlemen.
World’s best-selling battery brand
-
+100,000 satisfied customers
More than 100,000 customers already trust baterias.com — and recommend us to their friends and family.
They trust us and recommend us
Choose trust, choose quality, choose baterias.com.