Exide ELT9B · Motorcycle battery 12V 3Ah 190A Li-Ion
Specifications
| Brand | EXIDE |
|---|---|
| Part number | ELT9B |
| Voltage (V) | 12 |
| Capacity (C20) | 3Ah (c20) |
| Technology | Li-Ion |
| Length | 150.00 cm |
| Width | 65.00 cm |
| Height | 92.00 cm |
| Weight | 0.70 Kgs |
€90.80
VAT included
Exide ELT9B 12V 3Ah 190A is a sealed motorcycle battery ready to fit, with the JIS reference your mechanic recognises at a glance. Vibration-resistant, keeps voltage during the winter off-season and cranks first time when you take it out for a ride.
Why this motorcycle battery?
- Same JIS referenceas your bike's original — fits first time
- Sealed and ready to useno acid handling, no refills
- Survives winter storageholds charge through long off-season
JIS code
ELT9B
Voltage
12 V
Capacity
3 Ah
Cold cranking
190 A
Dimensions
150×65×95 mm
Technology
Litio (LiFePO4)
Polarity
Positive on the left
Weight
0,7 kg
Model
EXIDE MOTO LITHIUM
Mfr. reference
ELT9B
Lithium motorcycle battery Exide ELT9B Moto Litio 3Ah 190A 12V
12VVoltage
3AhCapacity
190ACold cranking
0.70kgWeight
Designed for motorcycles and quads looking to save weight and gain cranking power, the LiFePO4 Exide ELT9B cranks hard and weighs a fraction of an equivalent lead-acid battery. Its 150 × 65 × 92 mm and the positive terminal on the left make it the exact replacement for the 3 Ah battery fitted as standard to many motorcycles.
- Instant cranking even after weeks of standing.
- Built-in BMS protecting the battery and the vehicle.
- Battery management system (BMS) protecting against overcharge and short circuit.
- No acid, no maintenance, mounts in any position.
What the Exide ELT9B is for
The Exide ELT9B is designed for motorcycles and quads looking to save weight and gain cranking power. Check that your bike's regulator delivers a charging voltage compatible with lithium (normally up to 14.6 V). Check that it matches your current battery in dimensions, terminals and hold-down: this reference has a weight of 0.70 kg, M12 terminals and B0 hold-down.
Size, terminals and hold-down of the Exide ELT9B
It has external dimensions of 150 × 65 × 92 mm and weighs 0.70 kg. The positive terminal on the left decides which side the cables end up on: it is the detail that causes most buying mistakes, so check it before ordering. It uses a B0 hold-down and M12 terminals, the system that anchors and connects it in the vehicle. Before replacing it, measure your current battery tray: if all three dimensions and the terminal positions match, the swap is direct and needs no adapters.
The Exide ELT9B: Moto Litio range and LiFePO4 lithium technology
The ELT9B is part of the Exide Moto Litio range. Choosing the right reference within the series comes down to capacity, dimensions and terminals: technology and quality are common to the whole family.
A LiFePO4 battery starts with the same nominal voltage as a lead-acid one but with far less weight and a service life several times longer. It requires a lithium-compatible charger.
Exide: the maker behind the ELT9B
Exide is one of the world's largest battery manufacturers and an original-equipment supplier to many car makers. Its European plants produce starter, industrial and leisure batteries under original-equipment quality controls. We guarantee that every Exide arrives new, charged and with the manufacturer's full warranty.
Manufacturer's warranty
The Exide ELT9B comes with the manufacturer's official warranty. Always charge with a LiFePO4-compatible charger: a lead-acid charger with a desulphation phase can damage it and void the warranty.
How to make it last longer
Always use a LiFePO4-compatible charger and avoid the desulphation modes of lead-acid chargers. Store the battery at 50-70% charge if it will be unused for months.
Delivery times and returns
Same-day dispatch from our warehouse for in-stock orders placed before 6:00 pm: 24-48 working hours in mainland Spain and Portugal, 3 to 5 days in the islands and the rest of Europe. Returns are accepted for 14 days if the battery has not been used (free collection on the Iberian mainland). You will receive tracking by email.
BCOM-EXIDE-ELT9B
Data sheet
- Brand
- EXIDE
- Reference
- ELT9B
- Model
- EXIDE MOTO LITHIUM
- Voltage (V)
- 12
- Length
- 150.00 cm
- Width
- 65.00 cm
- Height
- 92.00 cm
- Weight
- 0.70 Kgs
- Technology
- Li-Ion
- EAN
- 3661024036849
- Terminal layout
- Positive terminal on the left
- Terminal type
- M12
- Hold-down
- B0
- Cold cranking amps (EN)
- 190A
- Capacity (C20)
- 3Ah (c20)
- Energy (Wh)
- 36
Specific References
- EAN13
- 3661024036849
- MPN
- ELT9B
Codes and references Exide ELT9B
| Brand | Exide · see all batteries Exide |
|---|---|
| Manufacturer range | EXIDE MOTO LITHIUM |
| Manufacturer reference (MPN) | ELT9B |
| EAN-13 barcode | 3661024036849 |
| Dimensions (length × width × height) | 150 × 65 × 95 mm (150x65x95) |
Recommended accessories
How to change the battery
Guide to replace your motorcycle battery in 10-15 minutes. Motorcycle batteries are light (2-5 kg) and usually need an 8 mm wrench.
Step 1. Prepare the vehicle
Park on a flat surface, switch off the engine and remove the key. Make sure all lights and electrical accessories are off. Wait 1-2 minutes before starting.
Step 2. Locate the battery compartment
On motorcycles it is usually under the seat, in the rear cowl or behind a side panel. Check the manual — access varies a lot between models.
Step 3. Disconnect the negative (−) terminal
Use the 10 mm wrench to loosen the negative cable nut (black, marked −) and remove the cable from the post. Move it aside so it cannot touch any bodywork.
Step 4. Disconnect the positive (+) terminal
Repeat with the positive cable (red, marked +). Important: never let a terminal touch metal of the car while the other is still connected.
Step 5. Remove the old battery
Loosen the hold-down clamp or the straps that secure it. Lift the battery carefully — typical weight 2-5 kg. Check the terminals are not corroded before fitting the new one.
Step 6. Install the new battery
Place the battery in the same orientation as the old one (positive terminal on the same side). Tighten the hold-down clamp firmly.
Step 7. Connect the cables
Connect the positive (+) terminal first, then the negative (−). Tighten the nuts with the wrench until each terminal does not move. Apply anti-spark grease if you have any.
Step 8. Verify the engine starts
Close the bonnet. Start the engine to confirm everything works. On cars with Start-Stop or a BMS, you may need to register the battery via OBD so the alternator applies the correct charging profile.
Frequently asked questions
How do I change this battery step by step?
In most motorcycles it fits in 15-30 minutes with a 10 mm wrench; if the battery is under the seat or in the boot the time can double. See the step-by-step guide on this page. Quick summary: 1) switch off the engine and remove the key; 2) locate the original battery (engine bay, boot or under seat); 3) disconnect the negative (−) terminal first, then the positive (+); 4) loosen the hold-down clamp and remove the old battery; 5) fit the new one in the same orientation — match the polarity shown on the product sheet; 6) connect the positive (+) first, then the negative (−). On motorcycles with Start-Stop or BMS, register the battery via OBD so the alternator applies the correct charging profile.
How long does the Exide ELT9B battery last?
Expected lifespan of the Exide ELT9B is 4 to 7 years in regular use (depends on technology and climate). In cold regions it drops slightly due to cold-start stress; in very hot regions it also drops because of electrolyte evaporation. To extend its life: avoid deep discharges (headlights on with engine off), have the alternator checked yearly, and keep the battery clean and properly secured.
What are the dimensions of the Exide ELT9B battery?
Dimensions (length × width × height) are 150×65×95 mm — also written as 150x65x95 mm — following the European DIN standard. Always measure the space in your motorcycle before buying: even one extra millimetre can prevent the hold-down clamp from closing. The height shown includes the terminals.
Is the ELT9B valid for my vehicle?
Three options to confirm: 1) enter your number plate in the finder (DGT/DVLA/KBA auto-detect your model and engine); 2) check the "Compatible vehicles" tab on this page, where we list every vehicle verified by our technical team; 3) if you cannot find your model, message us on WhatsApp with brand, model, engine and year — we reply during business hours (Mon–Fri 10:00–13:30 and 16:40–18:00 (Spanish time, CET)). The ELT9B typically fits a wide range of European vehicles thanks to its standard DIN case format.
Which batteries are equivalent to the Exide ELT9B?
Directly interchangeable batteries (same dimensions, same polarity, same Ah and CCA) are the OEM equivalents from leading brands: Bosch, Tudor, Exide and, depending on the model, Banner or Yuasa. Exact equivalence depends on technology — an EFB cannot be replaced with a conventional battery in Start-Stop motorcycles. See the "Equivalents" section to view recommended options at the same performance level.
The top-rated online battery store in Spain
-
Audited by Trustpilot, no filters, no edits. The top-rated battery store in Spain.
Trustpilot · verified, no filters
-
Official Varta distributor
Official Varta wholesale distributor. 100% genuine batteries, recently manufactured, best price and no middlemen.
World’s best-selling battery brand
-
+100,000 satisfied customers
More than 100,000 customers already trust baterias.com — and recommend us to their friends and family.
They trust us and recommend us
Choose trust, choose quality, choose baterias.com.